SuperSteer® Bell Crank & Bell Crank Arm Steering Controls
Now, you can help eliminate “white knuckle” RV steering (and all the fatigue that goes with it), road wander and rut tracking with SuperSteer® Bell Crank Steering Controls
Drive more relaxed. SuperSteer® Bell Cranks (P3032) & (SS100) reduce steering wheel free-play and help minimize constant correction. By test, steering controls perform “better than new.”
We designed the P-3032 Bell Crank to fit motorhomes for the Chevy/Workhorse P30 & P32 chassis. The P3032 also fits the G30HD & G3500HD Chassis.
Click here to see the SuperSteer® SS100 Bell Crank (pictured right) — same product designed to fit the Freightliner XC and the Magnum chassis.
Heavy-Duty Engineering
Both the P-3032 and the SS100 offer similar precision engineering that give you tighter motorhome steering, more steering control, & longer life than OEM parts.
These Bell Cranks feature:
- Chromemoly heat-treated steel shaft.
- Hi-tensile strength casting, spindle & tapered roller bearings.
- Grease-packed & sealed to keep out dirt and water for life.
- You can adjust these bell cranks to return them to like-new performance.
- They’re maintenance-free.
Comparison
● Pictured left - Factory OEM bell
crank. Note the use of sleeve bushing.
● Pictured right - P30-32 Bell Crank. Note the use of
tapered bearings
protected inside
the sealed unit.
Minnesotan Glenn Rasmussen tells his
story here about how he found
Henderson’s through the Internet
Why SuperSteer® Works So Well
Straight bushings in standard bell cranks can’t be preloaded like a tapered roller bearing. This means a certain amount of clearance always allows play between the bushing and shaft.
The Difference: The SuperSteer® Bell Crank uses tapered roller bearings on a hi-strength steel shaft. It’s installed with a pre-load so it’s much tighter and allows far less wear.
Endurance Tested: A test proved these Bell Cranks 19% tighter than a set of rebuilt bell cranks with simple bushings. The high-quality tapered roller bearings remain tight with no lateral (side-to-side) or vertical movement after testing. The SuperSteer® unit outlasted the OEM unit many times over, which justifies its lifetime warranty.
What Steve & Beverly Heising Say
“Our motorhome …pulled to the side and wouldn’t track down the highway. Henderson’s installed SuperSteer bell cranks, springs, & a sway bar. We had already researched [Henderson’s] on the Internet…came highly recommended. They were very helpful. Got us right in, stayed overtime to finish the job – even took care of an electrical problem. – Steve & Beverly Heising, San Diego CA
After a SuperSteer® Bell Crank installation, one motorhome owner commented his RV steering control was much tighter and more responsive. What’s more, he felt less driver fatigue.
Bud Weisbrod has some choice
thoughts about bell cranks here
SuperSteer® increases motorhome steering control noticeably over stock OEM bell cranks.
Life-Long Warranty
These SuperSteer® Bell Cranks are warranted as long as you own your coach.
Henderson’s Guarantee When you have your Bell Cranks installed at Henderson’s, we guarantee our work risk-free. If you’re not satisfied, you get your money back.
SuperSteer Bell Cranks work. “Hooray, the wandering steering on my Trek 24 has been fixed thanks to Henderson’s Line-Up. First, I put on your SuperSteer® bellcrank support and there was a noticeable improvement. Then I had it aligned using Henderson’s settings (quite different from Chevrolet’s) and I am satisfied.” Robert Hayward, Seattle, WA
SuperSteer® Bell Crank Arms
“We leave nothing to chance”
It may seem unimportant, but this little gadget is a vital part of your RV steering system. In addition to the Bell Crank, the Bell Crank Arm must be checked to make sure it’s tight and doesn’t allow play.
A worn bell crank arm can contribute to less responsive steering control. We always recommend you have this pivotal joint checked for wear and replacement if needed.
With this improved design, you drive relaxed while maintaining crisp, precise motorhome steering & control in high wind and road ruts. You steer your rig with much less fatigue, and the system requires virtually no more attention.
You can have your bell cranks installed by Henderson’s trained technicians OR you can have them shipped to you. If you’d like to order one or get more information, please phone toll-free 888-898-3281 & order from our SuperSteer® Division. You can also E-mail SuperSteer® at sales@superstop.com here.
If you’d like an installation appointment or more information about SuperSteer® bell cranks, call Henderson’s at the number below –
Henderson’s Line-Up
417 S.W. Henderson Lane
Grants Pass, OR 97527
- Phone us at: 541 479-2882
- “800″ Phone: 800-245-8309, Ext 1
- Fax us at: 541-955-6164
- Office Hours: (PST) 8 a.m. - 5 p.m. Mon-Fri; Closed Noon
to 1 p.m. If you call after hours, we'll call you back. If you’re driving & unfamiliar with the area, see a map here
E-mail us at:
Share this:
Henderson's Line-Up, Brake & RV, Inc.